16f877a with ds18b20
1 Attachment(s)
gởi các bạn tài liệu để tham khảo:
|
Đang bị stress với con DS18b20 này, để test thử code chạy ok o. Thk bạn nhiều.
|
Mạch đã chạy, giải tỏa được stress, một lần nữa xin cảm ơn bạn tdm rất nhiều.
|
con tuyet chieu nao ko gui len luon
|
bác thử kết nối thêm realtime 1307 gt I2C chưa . e làm đang làm con này thêm 1307 mà vẫn chưa chạy
|
Trích:
|
xin sua giup code , minh dang lam do an nhiet dung 18b20 wet led 7 doan.thank
#include<16F877A.h>
#device *=16 #fuses HS,NOPROTECT,NOLVP, NOWDT, NOLVP, NOBROWNOUT,NOPUT #USE delay(clock=2000000) #define TOUCH_PIN pin_a0 #include<touch.c> void hienthi(int8 a,int8 b,int8 c); int8 const seg7[10]= {0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90 }; //chuong trinh chinh======// void main(){ int8 tam1=0,tam2,ss,i; int8 led1,led2,led3; int16 nd; //=====cai dat chuyen doi nhiet do 9bit======== //======================== touch_present(); touch_write_byte(0xcc);// phat lenh skip ROM touch_write_byte(0x4e);// phat lenh ghi 2byte du lieu to Scratchpad touch_write_byte(0x33);// ghi 2 byte Trong touch_write_byte(0x33);// touch_write_byte(0x1f);// cau hinh cho thanh ghi nhiet do (do phan giai 9 bit) touch_present(); touch_write_byte(0xCC);// skip ROM touch_write_byte(0x48);//Sao chep Sratchpad vao Eeprom //====vong lap chuong trinh chinh=====// while(TRUE){ do{ if(touch_present()) { touch_write_byte(0xCC); touch_write_byte(0x44);//xuat lenh chuyen doi nhiet do for(i=0;i<7;++i) { hienthi(led1,led2,led3); } touch_present(); touch_write_byte(0xCC); TOUCH_WRITE_BYTE(0xBE);//lenh doc bo nho nhap tam1=touch_read_byte();//doc 2 byte nhiet do tam2=touch_read_byte();//doc 2 byte nhiet do } } while(tam1==ss);// so sanh gia tri nhiet do doc duoc voi gia tri truoc do ss=tam1; //==chuyen doi nhiet do sang so thap nhan==== nd=make16(tam2,tam1); nd=nd>>4;//dich phat 4 bit nd=nd&0x0ff;//lay 8 bit thap if(bit_test(nd,7))//neu gia tri nhiet do am { led3=10;//led3 hien thi dau""-"" nd=~(--nd);//lay bu 2 gia tri nhiet do nd=nd&0x0ff;// xoa byte cao } else// neu gia tri nhiet do duong { led3=nd/100;//led3 hien thi so hang tram nd=nd%100; } led2=nd/10;//led2 hien thi so hang chuc led1=nd%10;//led1 hien thi so hang don vi } } //chuong trinh hien thi_quet led=== void hienthi(int8 a,int8 b,int8 c) { output_b(seg7[a]); output_low(pin_d7); delay_ms(1); output_high(pin_d7); output_b(seg7[b]); output_low(pin_d6); delay_ms(1); output_high(pin_d6); output_b(seg7[c]); output_low(pin_d5); delay_ms(1); output_high(pin_d5); } |
xin sua giup code , minh dang lam do an nhiet dung 18b20 wet led 7 doan.thank
#include<16F877A.h>
#device *=16 #fuses HS,NOPROTECT,NOLVP, NOWDT, NOLVP, NOBROWNOUT,NOPUT #USE delay(clock=2000000) #define TOUCH_PIN pin_a0 #include<touch.c> void hienthi(int8 a,int8 b,int8 c); int8 const seg7[10]= {0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90 }; //chuong trinh chinh======// void main(){ int8 tam1=0,tam2,ss,i; int8 led1,led2,led3; int16 nd; //=====cai dat chuyen doi nhiet do 9bit======== //======================== touch_present(); touch_write_byte(0xcc);// phat lenh skip ROM touch_write_byte(0x4e);// phat lenh ghi 2byte du lieu to Scratchpad touch_write_byte(0x33);// ghi 2 byte Trong touch_write_byte(0x33);// touch_write_byte(0x1f);// cau hinh cho thanh ghi nhiet do (do phan giai 9 bit) touch_present(); touch_write_byte(0xCC);// skip ROM touch_write_byte(0x48);//Sao chep Sratchpad vao Eeprom //====vong lap chuong trinh chinh=====// while(TRUE){ do{ if(touch_present()) { touch_write_byte(0xCC); touch_write_byte(0x44);//xuat lenh chuyen doi nhiet do for(i=0;i<7;++i) { hienthi(led1,led2,led3); } touch_present(); touch_write_byte(0xCC); TOUCH_WRITE_BYTE(0xBE);//lenh doc bo nho nhap tam1=touch_read_byte();//doc 2 byte nhiet do tam2=touch_read_byte();//doc 2 byte nhiet do } } while(tam1==ss);// so sanh gia tri nhiet do doc duoc voi gia tri truoc do ss=tam1; //==chuyen doi nhiet do sang so thap nhan==== nd=make16(tam2,tam1); nd=nd>>4;//dich phat 4 bit nd=nd&0x0ff;//lay 8 bit thap if(bit_test(nd,7))//neu gia tri nhiet do am { led3=10;//led3 hien thi dau""-"" nd=~(--nd);//lay bu 2 gia tri nhiet do nd=nd&0x0ff;// xoa byte cao } else// neu gia tri nhiet do duong { led3=nd/100;//led3 hien thi so hang tram nd=nd%100; } led2=nd/10;//led2 hien thi so hang chuc led1=nd%10;//led1 hien thi so hang don vi } } //chuong trinh hien thi_quet led=== void hienthi(int8 a,int8 b,int8 c) { output_b(seg7[a]); output_low(pin_d7); delay_ms(1); output_high(pin_d7); output_b(seg7[b]); output_low(pin_d6); delay_ms(1); output_high(pin_d6); output_b(seg7[c]); output_low(pin_d5); delay_ms(1); output_high(pin_d5); } |
thank cac bac nha minh cung dang lam ma chua dc.hi vong vot xong code ban share minh se lam duoc
|
moi nguoi oi giup minh voi ! minh dang viet chuong trinh bang ccs cho pic16f877a doc nhiet do tu ds18b20 hien thi len lcd 16x2 .ma khong the nao doc nhiet do tu ds18b20 duoc luc nao lcd cung hien thi 84 ma minh tang giam ds18b20 thi tren lcd van khong thay doi. minh cung lam mach that va mo phong tren protues nhung ket qua nhu nhau thoi,cao thu nao xem giup minh sai cho nao voi ?. minh up code va mo phong o link duoi.
http://www.mediafire.com/?ood3ibt0qd1j3iw #include <16F877A.h> #fuses XT,NOWDT,NOPROTECT,NOLVP #device adc=16 #include <lcd420.c> #include <math.h> #define dp pin_c0 #use delay(clock=4000000) //---------reset-------------- void reset() { output_low(dp); delay_us(500); output_float(dp); delay_us(500); } //-------------------------read---------------------- int read() { int a,data; for(a=0;a<8;a++) { output_low(dp); delay_us(10); shift_right(&data,1,input(dp)); delay_us(45); output_float(dp); delay_us(2); } return(data); } //----------------------write----------------------------- void write(int data) { int a; for(a=0;a<8;a++) { set_tris_c(0x00); output_low(dp); delay_us(15); output_bit(dp, shift_right(&data,1,0)); delay_us(45); output_float(dp); delay_us(2); } } //---------------------chuong trinh chinh------------------- void main() { int8 data,tem1,tem2,busy=0; int16 temp; float t; reset(); write(0xcc); write(0x44); delay_ms(1000); while(busy==0) busy=read(); reset(); write(0xcc); write(0xbe); tem1=read(); tem2=read(); temp=make16(tem2,tem1); temp=temp>>4; t=(float)(temp); while(true) { lcd_init(); lcd_gotoxy(1,2); t=(int8)floor(t); printf(lcd_putc,"%x",t); delay_ms(1000); } } |
bạn phải đọc byte 2,3 của bộ nhớ nháp chứ! ở trên mình thấy bạn mới chỉ đọc đến byte0 và 1 chứ mấy
|
thank bạn nhiều, mình đang cần cái này.
|
Múi giờ GMT. Hiện tại là 12:27 PM. |
Tên diễn đàn: vBulletin Version 3.8.11
Được sáng lập bởi Đoàn Hiệp.
Copyright © PIC Vietnam